Sedona Star Month 1 Points

After so much time at the sewing machine over the past few days, my back was really complaining, so I've been taking it slower again.  I've been doing the log cabin points a few at a time:

Four more to go!  You'll be seeing a lot more of these particular fabrics as the quilt progresses.  An unexpected benefit of using solid fabrics is that there is no wrong side, which makes the paper piecing even easier.  I hope, though, that it does not make me sloppy once I progress to prints later in the quilt.

It's been really fun so far.  The finished points have a satisfying weight to them, with the fairly thick Kaufman Kona Solid fabric, and the Ricky Tims Stable Stuff on the back.  I've been using 1/4" seams too.  The instructions call for 1/8" seams, but as a new paper piecer I just didn't feel comfortable with that.  If I pay for it later, so be it.

Many people have also mentioned the somewhat frugal cutting instructions for the quilt.  Because I was planning to use a wider seam allowance, I just measured the widths right off the template.  I ended up adding 1/4" to the width, and about 1/2" to the length for these pieces - it may have been more for some of the others.  I have lots of fabric, so I am not worried about running out!

Beginning to Paper Piece Sedona Star

I was very excited to actually start sewing Sedona Star!  I began with the ring on Month 1, because that looked the easiest to me:

The light colour here is actually this light purple fabric.  The camera made it blue.  But the piecing went really well.  I very nearly sewed the two ends wrong sides together, even after reminding myself about it!  But fortunately I realized my mistake before actually sewing it.  I was so encouraged by this initial success that I moved on to the centre star:

I realized a few things when I was about halfway through this.  The first was that my colour scheme is not going to leave me any room for error!  I deliberately chose the high contrast scheme to show off the more difficult parts of the quilt.  I wasn't thinking though, that it meant I am going to have to do those parts really well.  Anyway, so far, so good.  I'll have to be super careful with those points when I sew the two circles together.

The second issue is that the dark fabrics really show lint!  I can see that this is going to be a problem for the lifetime of the quilt.  It looks much worse in the photo because the flash picked out the light particles.  I wondered where all that lint was coming from, and I realized that it is from the Ricky Tims Stable Stuff.  It is shedding tiny, shiny, polyester fibres as I work with it.

On the TQS forum Margo suggested that I can wash the finished flimsy to remove all the Stable Stuff before I quilt it.  Now that I've seen how these fibres stick to the fabric, I don't think that will be an option.  For now, I'll just use a good lint roller before I take any final photos!

Otherwise, though, the Stable Stuff is a dream to work with.  It is much easier to use for paper piecing than the vellum was.  It makes a very clean fold when you are cutting the seam allowance.  The vellum didn't always want to fold along the line, but with the Stable Stuff there is no problem.  And because the Stable Stuff is more like Pellon interfacing, it doesn't remember all the fold lines, so you can wrinkle it up all over and it still goes back to lying flat when you're done.

When I lay the two parts together, it looks like this:

My intention with the centre of the quilt was to keep it simple, and I am satisfied with the result so far.  The main focus of the quilt will be the applique blocks we're doing this summer, so I didn't want to do too much here.  I'll show you one or two of the log cabin points tomorrow, and then it'll be on to the applique circles!

Preparing the Templates for Sedona Star

Well, I had a busy weekend.  I finally started Sedona Star!  Hard to believe, I know.  :)

Saturday night I put together the templates.  What a tricky job!  I have a feeling this was probably the most fiddly bit of the whole quilt.  But, if they are right, everything will go smoothly, so I didn't rush it.

The grey gridlines were a huge help.  I ended up cutting the templates just a millimetre or two away from the outside gridline, and butting them up against the edge of my Olfa mat, which I used as a ruler.  This allowed me to make sure that the overall measurement was 12" for the inside template, and 18" for the outside one.

I am using the Ricky Tims Stable Stuff for my templates.  As designer Sarah Vedeler suggested, I used Lite Steam-A-Seam 2 in the 1/4" width to hold them together.  It was pretty convenient to use, and held the pages together well.  Before I tried it I was worried about it adding bulk to the quilt. I found, however, that there is almost nothing to it, so added weight is not a worry.

There were no gridlines for Template 2, which is the ring with the appliqued circles.  To make sure that it would fit properly inside the outer ring, I used the assembled Template 3 as a guide:

I carefully lined up the solid stitching lines on each template (not the cutting lines!).  Template 3 has convenient marks for each section of Template 2, so it is easy to lay it right in place.  I worked my way around the ring, ironing each section to the previous one as I went:

I am not ironing the two layers together, just using the bottom layer as a guide.  Once it was finished, I knew it would fit into the outer ring perfectly.

Hopefully, with these tricks in my toolbox, assembling the templates in future months will be less painful.  Fortunately, the paper piecing on Sunday went really well.  I'll show you tomorrow!